Spacelog Apollo 13

Okay. You ready to press on?

I'm ready.

Okay. Just reminded we owe somebody a BAT B voltage.

Okay, another volts and amps coming up.

All right. Thank you. And this left us in P52 with two marks, and we'll go ahead and torque the NOUN 93s.

Okay. … torque the NOUN 93s, after the two marks.

Okay. So that gives us a good platform. Now the LM will maneuver to the jettison attitude, and the only thing of significance here is that you want to watch to make sure that the path they choose to go to the jettison attitude avoids gimbal lock on your own platform.

Okay. The LM maneuvers to the jettison attitude and I just monitor the maneuver and yell at Jim if he gets near a gimbal lock.

That's affirmed. Okay, and then the LM will go to a MAX deadband attitude hold in the jettison attitude.

Okay. The LM goes to MAX deadband attitude hold.

Okay. Now we're ready to go back to work. The next thing we'll do is to continue to powerup procedures. Do you have any further questions on that alinement, Jack?

No. No. I think—I think it's all self-explanatory now.

Okay. The one thing that everybody would like for you to understand is we certainly don't insist on using the Moon and the Earth; if you find you have good stars, why use them. However, this alinement is more than adequate to give us a good guided entry.

Okay. If I get a set of good stars, do I start right out to a basic P51 and a P52 option 1?

That's affirmative.

Okay.

Okay. Now, we're ready to go to work on panel 275. And it starts with a circuit breaker MAIN A —

Wait—wait just a minute. Wait just a minute. I owe you some volts and amps.

Okay. All right.

Okay. Volts are 39.4, amps, 1.25.

Okay. I thought maybe, your meter was stuck before.

No (laughter).

All right. You ready to go back to 275? Have a circuit breaker MAIN A, BAT BUS A, closed.

CB MAIN A, BAT BUS A, closed.

That's correct. And circuit breaker MAIN B, BAT C, closed.

CB MAIN Baker, BAT Charlie, closed.

Okay. That's correct. Now we're up to EI minus 1 plus 30. And at this time, we're going to proceed with the closeout and hatch installation.

Okay. Closeout and hatch installation at EI minus 01:30.

That's right, Jack, and we're going to close the LM hatch, and we'll make the dump valve in the LM hatch closed.

Understand you're going to close the dump valve, now on the LM hatch, right?

That's correct.

Okay. This is a change from what we had understood previously.

That's correct.

I'm—Personally, I'm happy to see it, but that's good.

That's correct. Okay, now. Circuit breaker ECS TRANSDUCER, TEMPERATURE, MAIN A and MAIN B, that's two of them, closed.

CB ECS TRANSDUCER, TEMPERATURE, MAIN A and MAIN B, closed.

That's correct. On panel 4: PRIMARY ECS GLYCOL PUMPS, one, to AC 1.

Primary ECS GLYCOL PUMPS to 1, AC1.

That's correct. Okay, then we'll finish going back to the tunnel vent, and verify the LM/CM DELTA-P and make sure it's been holding pressure. And we'll come back again and rehash all of the hatch integrity check and tunnel vent procedures with you. The next thing I want to read off is the EI minus 1 plus 20. We'll go to panel 7: BMAG number 1 POWER to WARM UP.

BMAG number 1 POWER to WARM UP.

That's correct. Then at EI minus 1 plus 10, we'll perform SCS powerup per checklist, page G/2-4.

Okay. Perform SCS powerup per G&C checklist, page 2-4.

That's correct. Okay, on panel 4: SUIT COMPRESSOR NUMBER 2 to AC1.

SUIT COMPRESSOR 2 to IC1.

That's correct. SPACECRAFT CONTROL to SCS.

SPACECRAFT CONTROL to SCS.

Okay. And your MANUAL ATTITUDE switches, as you desire. We're coming up on jettison of the LM, so that's just like separation.

Okay.

Okay. And we'll do a GDC aline.

Okay. Perform a GDC aline.

Okay. On panel 8: ROTATION CONTROL POWER, DIRECT, 1 and 2, MAIN A/MAIN B.

Okay. These are circuit breakers, ROTATION CONTROL POWER, DIRECT, 1 and 2, MAIN A and MAIN B, closed.

Okay, Jack. I was thinking switch. Let me verify that's a circuit breaker, too. I think we have to get both of them.

Okay, there's those four circuit breakers over there, Ken. When you said panel 8, that's what I thought you were talking about. I don't think the circuit breakers are out right now, but why don't we just put—verify the circuit breakers and put the switches to MAIN A/MAIN B.

Okay, that's correct, Jack. Okay, at EI minus 1 hour, we're going to be doing the LM jettison; so just prior to that, we want to do a P47.

Okay, say at about 1 minute prior to LM jettison, huh?

Yes, just something that's comfortable for you.

Okay.

All right, after we've? done that, we want to get panel 8, SEQUENTIAL, PYRO ARM, two of them, ON.

Okay. I get a GO from MSFN for this?

Okay, John says we can watch it.

Okay.

All right; the next thing is CSM/LM FINAL SEP, two of them, ON, up.

CSM/LM FINAL SEP, two, ON.

That's correct. Now we're going back to panel 8, and it's SEQUENTIAL, PYRO ARM, two of them, to SAFE.

Okay. SEQ PYRO ARM, two, to SAFE.

That's correct, and go back to P00.

Okay. Go to P00.

All right. And now it's time to configure for single ring.

Okay. Configure for single ring RCS.

That's right, and since you're still an hour from EI, I guess it wouldn't hurt to use MINIMUM IMPULSE or something like that rather than the DAP, at least not until you get closer down. We'll have the DAP loads for you later.

… —

Okay. And as soon as you've gotten yourself all set up with a good control mode, you want to maneuver to the entry attitude.

Maneuver to entry attitude per the pad.

That's correct. And we show EI minus 55, which really means when you get to the entry attitude, we have a sextant star check for you. And that will be on the pad.

Okay. Perform a sextant star check.

Okay. And I want to remind you to park the optics at 90 degrees of shaft.

Okay. Say again why, Ken. I didn't understand that.