Spacelog Apollo 13

It's going to take you about 15 hours.

Jack, about how many amperes of LM power will this 15 hours …?

Stand by. We'll get it for you —

How many, Jack?

Okay. He got it. He got the question.

Okay, Jack. That's going to take 120 amp-hours out of the LM, which is equivalent to 10 hours, which will put us back to 193 hours, and that's plenty.

Okay. Let me relay that to Jim here. It'll be 120 amp hours, which leaves us—which puts us back from 203 hours … to 193 hours.

Yes, there's that much to spare.

Okay, Jack. One question here. If we have any problems setting up this LM power to the CSM, is the quickest way to get out of it, return to the normal configuration, as it is for me to just switch the LM POWER to CSM to RESET then OFF?

Stand by 1.

I would like to give one quick step in case that gave Jim report some sort of problem for us to get out of it quickly.

Okay. Let us talk it over for a minute, Jack.

Okay, Jack. Are you with me?

Yes. We're still here, Jack. What we want to do is follow you through on this, so we're going to get high bit rate to do it. In answer to your question, to undo this procedure quickly, in the event a problem develops, be sure that you don't touch the 124 POWER switch because it's got a RESET position. But the way to undo it is go into the CSM and on panel 5 open two circuit breakers. And they're some of the first ones we read to you. Open LM POWER-1 MAIN B, and open LM POWER-2 MAIN B. You copy that?

Okay. Understand. If I want to get out of this real quickly, I have to open just two circuit breakers in the CSM; that's on panel 5, LM POWER-1 MAIN B, LM POWER-2 MAIN B.

Okay. And before you go ahead with this, let's establish high bit rate and wait 1 on that. And then as we go through the procedure we want you to wait when you get power on MAIN B so we can take a look at MAIN B without any loads on it before we start charging the batteries.

Okay. I understand you want high bit rate on the LM or CSM just before we start this?

That will be high bit rate on the LM, and stand by for it.

Okay.

Okay, Jack. Before we go ahead with this, what we want to do is read you the reverse—the normal reverse procedure.

Okay. I'm ready to copy.

Okay, Jack. I got the start on how you reverse this procedure. Ready to copy?

Go ahead, Jack.

Okay. First you want to reverse the battery charge procedure. To do that, on panel 3, switch BATTERY CHARGE, off; AC INVERTER 2, off; panel 5, MAIN BUS TIE BAT Alfa Charlie, on, up; panel 250, circuit breaker BAT Alfa, POWER ENTRY, and POSTLANDING, open. Read back.

Okay, Jack. On panel 3, BATTERY CHARGER, off, AC INVERTER 2, off; on panel 5, MAIN BUS TIE Alfa Charlie, on; panel 250, CB BAT A, POWER ENTRY and POSTLANDING, open.

That's affirmative, Jack, and then if you'll go back to the rest of the circuit breakers on that list, and just opposite—Open them all up. Stand by 1.

Okay, Jack. Go back to the battery charge procedure I gave you. And, in order to terminate charge, just—You'll just have to write “Open” or “Off” next to the circuit switch that I gave you. So on panel 250, that circuit breaker you've already opened; on panel 275, INVERTER POWER-2 MAIN B, open; panel 5, BAT RELAY BUS BAT A, open; EPS SENSOR UNIT AC BUS 2, open, EPS SENSOR SIGNAL AC2, open; BATTERY CHARGER, MAIN B, open; BATTERY CHARGER AC POWER, open; BATTERY CHARGER, BAT A CHARGE, open; INVERTER CONTROL 2, open; INVERTER CONTROL 3, open; you've already done the MAIN BUS TIE; and then BAT CHARGE switch to AC 1. Over on panel 3, you have already set the AC INVERTER 2 to OFF and then INVERTER 2 AC BUS 2, OFF; AC BUS 2 RESET to OFF. You have already put the BATTERY CHARGER switch to OFF; and your DC Indicator select to MAIN B. Over.

Okay. I'll be standing by to copy it.

Houston, 13.

Go ahead.

One thing I guess you probably all have considered it, but what heavy things can we store down there where the SRCs normally go to help increase our L over D?

I understand the question is what kind of heavy things can you store where the SRCs go.

Yes. They go down in the LEB underneath the computer, and the heavier things you have down there increases the L over D. We don't have any SRCs, so I was just wondering what heavy things—We could probably put some cameras, television cameras, things like that that normally pretty heavy down there in—that, in our SRC. No, we can't put the in our SRC, but we could put them in that container down there which would help decrease our L over D. Anything else you can think of would be greatly appreciated because we don't even have a throwaway station, so we're down a little bit in L over D.

Okay. Let me pass that question along, and get somebody working on it.

Souvenirs, I guess.

What souvenirs? (Laughter) All I've got is a Marine Corps foxhole-digging shovel.

You've got all you need then, buddy.

Okay. Ready to copy the power removal from the command module/LM umbilical.

I'm ready to copy. Go ahead.

Okay. This assumes that all the descent batteries are on line and ASCENT BATTERY 6 is on NORMAL FEED, as we said earlier. First thing you do is go in the CSM and look on panel 5 circuit breaker. LM POWER-2 MAIN B, open; LM POWER-1 MAIN A, open; circuit breaker EPS SENSOR SIGNAL MAIN B, open.

Hey, Jack.

Go ahead.

… You got just a little bit scratchy there because of the antenna problem. Let me read this back to you.

Okay. What I got, Jack, was the procedure assumes that all DESCENT BATTERIES are ON, and BAT 6 is on NORMAL FEED. Now we're going into the LM and on panel 5, we take LM, or CM LM POWER-2, MAIN B, open. And that's as far as I got.

Okay, the second one is on panel 5 also. Circuit breaker, LM POWER-1, MAIN A, open; circuit breaker EPS SENSOR SIGNAL, MAIN B, open. Okay, read those back for the CSM, and I'll give you some steps in the LM.

Okay.