Spacelog Apollo 13

Okay. On panel 3: the first three steps we took care of; MODE, VOICE, to VOICE; POWER, SCE, OFF; POWER PMP to OFF; and S-BAND OMNI would go back to Bravo. Panel 225: FLIGHT BUS, MAIN B, will go open; and CB CTE, MAIN B, will go open.

That's affirm. The two circuit breakers on panel 250 will go open; the two circuit breakers, panel 275, will go open. Okay, the circuit breakers on panel 250, we took care of already. Panel 3: AC INVERTER, 2, we took care of. AC INVERTER 2, AC BUS 1 should now go OFF. And the remaining two switches on panel 3 we took care of. And “Select best OMNI” remains the same. Okay. Read back.

Okay. The two switches—two circuit breakers on panel 250 will go back to open; the two circuit breakers on panel 275 back to open; the POWER ENTRY/POSTLANDING circuit breaker, we already took care of earlier; AC INVERTER 2; we took care of earlier; AC INVERTER 2 to AC BUS 1 will go to OFF; and AC INVERTER, AC BUS 1, we took care of—No, that'll go to OFF; and UP TELEMETRY, COMMAND RESET will go OFF.

That's correct, Jack. Okay, that's it. And I think we're about ready to go with this procedure whenever you are.

Okay. First we got to go through that procedure to power the CSM from the LM, is that Charlie?

No. No, this is independent of power from the LM. This is a—this is purely a CSM —

Okay.

This is purely a CSM powerup so we can take a look at your telemetry and see how cold the vehicle is and that sort of thing.

Okay. It's going in work.

Okay, now I won't—I won't have any voice with you, so—Is that right? You don't want me to get connected up—you want me to just take these readings and come back and tell you what I have, huh?

That's affirm. There'll be no voice. And —

Okay. Okay. In work.

I—we presume, though, that there'll be somebody in the LM that we can call if we have to get word to you.

Oh, yes. There'll be somebody to be standing by, they'll run up into the bedroom and tell me to stop what I'm doing.

Okay, and let us know when you start.

Okay. I'm going to start right now, Vance.

Okay.

Aquarius, Houston.

Aquarius, Houston. Over.

Okay, Houston; Aquarius. Switching watches, and Jack's going up into the command module.

Okay, Jim. We have four steps here to give you to request that you get back on DOWN VOICE BACKUP, if you're ready to copy?

Ready to copy.

Okay. Bit rate to LO bit rate. VOICE, FUNCTION switch to DOWN VOICE BACKUP. POWER AMPs CB, open; RANGE FUNCTION switch in RANGING; that's verify.

Okay. Bit rate, LO; VOICE FUNCTION, DOWN VOICE BACKUP; POWER AMP S-BAND, open; and RANGE FUNCTION to RANGE; and that's a verify. And I still have the BIOMED on RIGHT here, so we don't have hot mike.

Okay. Thank you.

And, you want that in work, now?

That's affirm.

Okay.

Okay. Houston, Aquarius. How do you read?

Loud and clear, Jim.

Okay. I have a question for you, Houston, if you have time.

Sure, go ahead.

And I'm copying down the reestablishing—PTC maneuver that Charlie gave me. Step 5 was, “When rates are less than 0.05 degrees per second, ATTITUDE CONTROL YAW to PULSE.” And just how am I to get my rates down to 0.05 degrees per second. My—My rate indicator, at the best, is 0.1 of a degree.

Stand by.

Aquarius, Houston.

Go ahead.

Jim, this has been tried in the simulator by Charlie and others, and what they recommend is that you null your rates on the error needles until you see no movement whatsoever, and then wait another couple of minutes, and that should do it. That's the only way we can tell. Over.

Okay. I'll give it the old college try.

Okay. And if you can't attain that, why, of course, just the best you can do. We'll have to give it a try. Maybe it won't be quite like the simulator.

Okay, Houston; Aquarius.

Go ahead, Aquarius.

Okay, Vance. I've gone all the way through your procedure—all the way down to “Select best OMNIs,” but I'm not getting any MAIN BUS B voltage and this I don't understand.

Roger.

I can read—I can read BAT—BAT BUS B voltage at 36.5. …

Okay, Jack. Do you read now?

I am not sure, Vance.

Okay. You faded out due to noise in the orientation. If you close the POWER AMP circuit breaker, we can hear you better. Over.

That's panel 16.

Okay, Vance. How are you reading now?

Okay. We're hearing you better. Stand by 1.

Okay, Jack. Please, repeat back now your conversation. You were cut out for—a while ago.

I don't have any idea where we cut out, Vance. I just said that we performed the procedure exactly as you say. We're down into the SEP critical portion to where I said, “select best OMNI.” However, we're not getting any MAIN BUS B voltage reading. I can read BAT BUS B, Baker, at 36.5; BAT Charlie at 37.0, but I have negative MAIN BUS B readings.

Okay. Stand by.

Okay, Jack. There are two—There's a switch and a circuit breaker that were positioned this morning that we'd like to have you check—Correction, just the switch. Panel 5, check your bus tie. MAIN BUS TIE BAT B/C on.

That is verified on. I checked that.

Okay.

Okay, Jack; this is Houston. Over.

Go ahead, Vance.

Okay. We're getting data from you, Jack, so that much looks good. On panel 5, request verification that EPS SENSOR SIGNAL circuit breaker is MAIN B. Over.

Okay.

Or it's —

— Stand by. —

— that MAIN B is closed.

Okay.

Okay, Jack. And, we see your MAIN BUS B voltage at 28-1/2.

Okay. You can see it. Good. Okay then. Okay, Vance. That circuit breaker is in.

Copy.

Well, Vance, if you're getting data from them, let me go back up there and finish the …

Okay, Jack. Please repeat, you're cutting out.

Okay, Vance. Okay. We just changed OMNIs here. I say, if you're getting data from us, that's the important thing. Let me go back up into the bedroom there and get the readings you wanted, so we can get this stuff powered down. Is that okay?

Okay, we'll get —

— by all means and —

— down there —

— select best OMNI —

— and then go back up.

Okay, Vance. We'll go back up—We've got voltage now, and we'll go back up and take the readings that you want.

Okay. And select best OMNI.

Okay. I'm going back up into the bedroom, Vance. How do you read?

Loud and clear.

Okay. I'm going back up to the bedroom. We'll select best OMNI and continue on with the procedure.

Roger.

Okay, Vance. Jim's up. How do you read?

Reading you loud and clear, Jim.

Okay.

And, Houston, I noticed through the AOT and through the overhead docking window that we are venting again.

Okay, Jim. Understand; the service module is venting.

That's affirm.

Aquarius, Houston.

Go ahead, Houston.

Jim, would you holler into the bedroom and tell Jack that when he has his onboard readouts that we wish he'd back—use the backout procedure and shut down again—per the procedure we gave him.

Roger. As soon as he—As soon as he gets his onboard readouts to use the powerdown procedure and shut down. Is that right?

That's affirm.

Okay. Jack just—Jack just told me that he's through, and he's going to go through the backout procedures again, the first one he's got is the shutdown.

Houston, Aquarius.

Go ahead, Aquarius.

Jack's ready to give you the readings if you are ready to copy them.