Spacelog Apollo 13

How do you read now, Jack?

Okay, Vance. Did you—how far did you—did you copy any of my steps there?

Okay, I heard you through AC INVERTER 2, AC BUS 1 to on, and you were cut out by noise. Go ahead.

Okay, Now comes to one I didn't understand. You said go over to MDC 5 and A in—AC INVERTER, AC BUS 1, RESET, then center, and then back to MDC 3; UP TELEMETRY, COMMAND RESET then OFF, and then select best OMNI.

Roger. The readback's correct, but let me recheck that. Stand by.

Jack, we were incorrect on panel 5; that should have been panel 3.

Okay, that's good. I got it.

Okay. Now, when you're in this configuration, the following onboard readouts are required. Panel 3: BAT C voltage, PYRO BAT A voltage, PYRO BAT B voltage, SPS HELIUM PRESSURE. And the following readouts on panel 101: CM RCS injector temperatures, those are positions 5 Charlie, 5 Delta, 6 Alfa, 6 Bravo, 6 Charlie, 6 Delta; and the battery manifold pressure, which is 4 Alfa. And standing by for readback.

Okay. You want me to read out on MDC 3: BAT B voltage, PYRO A voltage, PYRO B voltage, SPS HELIUM PRESSURE. On panel 101: command module RCS injector temperatures; 5 Charlie, 5 Dog, 6 Alfa, 6 Baker, 6 Charlie, 6 Dog. The battery manifold pressure, 4 Alfa.

Okay. Now—that was correct but I want to re-check the very first one, that was BAT Charlie voltage. Is that what you read back?

Okay. Okay, BAT Charlie voltage. Seems like we're having a difference—I can't understand BAT Charlie from BAT Dog.

Okay. Now, that—that complete procedure for getting into it, as far as getting into it's concerned. What I will give you now is how to back out of it after you're through with your readings. Are you ready to copy?

Okay.

Okay. Now you'll back out fairly quickly after you go into this procedure. All we'll need is about 5 minutes of TM, and so if you're ready to copy, here it comes.

Go ahead.

Panel 3: POWER AMPL to OFF. Incidentally, copy this down on a piece of scratch paper as I read it, and then later I'll refer back to your first list where you can write things in the right-hand margin.

Okay.

Okay —

Go ahead. You want—Repeat the one on panel 3 again, Vance.

Okay. POWER AMPL, OFF.

Okay. Go ahead.

TRANSPONDER, OFF. AC INVERTER, 2, to OFF. Okay. Next, panel 250: CB BAT Bravo, POWER ENTRY/ POSTLANDING to open. Stand by 1.

Okay, Jack. What I just gave you now on the backout is the only thing that's order critical. From here on, you can go to the steps for initiating the procedure, and backtrack. In other words, you should go to each of the panels that I read up and put the circuit breakers back to the base-line configuration—or the switches. Over.

Okay, now here's—to accent, here's the sequence-critical sets: POWER AMPL, OFF; TRANSPONDER OFF; AC INVERTER, 2, OFF; and the last one on panel 250, CB BAT Baker POWER ENTRY/POSTLANDING, open; and then hit the steps in reverse order that you gave them to me, and back out, like then I would start on MDC 3 UP TELEMETRY, OFF—to OFF; and then AC INVERTER—AC1 BUS 1 to OFF; and then AC INVERTER, 2, OFF; AC INVERTER, 2, MAIN B to OFF. Is that the type of order that you want to back out of?

That's affirm, but—just for kicks, let's go through these panels again, and I'll give you the—the position, just to make sure there can be no doubt.

Okay. Go ahead.

Okay. And once again in the—in the area where I said order was not critical, it's still not critical when you back out. But now I'll go ahead. Okay, panel 4: TELCOMM, GROUP 1, AC1, it will not be AC1, it'll go to OFF. Panel 5: all circuit breakers on that panel which were positioned will now come to opened. Over.