Spacelog Apollo 13

Okay; probably okay, Fred. Read it nice and slow so we'll be sure to get it. Over.

Okay. Jack pushed in the 250 BAT A, BAT B entry breakers. He read battery bus volts as 32.3 on A, 37.0 on B. Then he pushed in the 275 breakers tying the BATs to the main buses. In this configuration, MAIN A is at 32.0 volts, zero amps; MAIN B is at 37.0 volts, zero amps. So it looks like the buses are okay.

Okay, Fred. Copy those numbers and thank you very much. I assume you got them off all right.

That's affirm. We got all the breakers pulled again.

Hey, Houston; Aquarius. How do you read?

Aquarius, Houston. Go ahead.

Okay. How did our … configurations appear to be working down there?

I'm sorry, Fred, but we got noisy again there.

Okay. Let me know when you want me to try it.

Okay. That sounds better already. Go ahead.

Okay. I'd just like to … how's—how's our lith-o cartridge setup … appear to be working down there.

We are reading 0.2 on our CO₂ sets here, and we're all delighted. It seems to be working fine.

Boy, that is great.

And Fred, Houston. In a little while here, I'm going to have a procedure that I want to read up to you and have you copy down for future use. It's a procedure for powering the command module main bus off the LM, and it's something that we feel that's going to come in real handy later on for such things as popping off the command module entry batteries, and also possibly for doing some preheating and preliminary powering up of the command module before we get rid of the LM. We'll have that for you in probably 10 or 15 minutes. Over.

Okay, okay, Joe. That's good. Sounds good.

Roger.

Aquarius, Houston.

Go ahead.

Okay, Fred. Our procedure-generating mill has generated another very short one for you here. It's a procedure for getting an onboard read-out —

Stand by 1, Joe.

Okay.

Okay. The PROPELLANT DISPLAY OVERRIDE circuit breakers are closed. … the propellant.

Right, Fred. The next step is simply to turn the PROPELLANT TEMP PRESS MONITOR switch to DESCENT 1, read the fuel and OX temps, turn it to DESCENT 2, read the fuel and OX temps; tell us what they are.

Okay. On DESCENT 1, I get a fuel temp of 66.5 degrees, OX … on DESCENT 2, I get …

Okay, Fred. We're in noisy COMM here; I got DESCENT 1 fuel 66.5; stand by a second.

Okay. How do you read, now …?

That's better. Go ahead.

Okay. You got 66.5 on DESCENT 1 fuel temp, oxidizer temp is 66 degrees.

Okay. Copy —

On DESCENT TANK 2, fuel is reading 60—Okay. DESCENT 2 fuel is reading 68 degrees; oxidizer, 65 degrees.

Okay. Copy that, Fred. Thank you. We'd like you to pull the circuit breaker, and we'll probably come to you again in 5 or 6 hours for another check.

Okay. The panel 16 … … ENGINE … OVERRIDE is open.

Aquarius, Houston. Over.

Aquarius, Houston. Over.

Go ahead.

Okay. We're chasing a small glitch that we saw a while ago in the O₂ flow rate which is now normal again, but what we'd like you to do is, first of all, to tell us whether, during that canister procedure, you moved O₂ DEMAND REG A to any position other than CABIN, and then we'd like you to move it to OFF momentarily and back to CABIN for us.

Okay. To answer your question, Joe, it's no. I checked the CABIN all the time. Qualitatively, when we switched to this configuration, it didn't seem like the frequency or the suit fan noise … decreased … logged down a little bit, but I'll follow your procedure. You want me to take REG A, go to close and back to CABIN; is that correct?

That's correct, Fred.

Okay. We're in close.

Okay.

Now, I'm back to CABIN.

Okay. Thank you very much, Fred. I'll get back to you if we see anything.

(Music—The Age of Aquarius)

… Thank you.

Hey, have you guys got a woman on board?

No way I could handle that.