Spacelog Apollo 13

Okay. That's correct, Jack. And now we'll go into the main bus powerup procedure. And the first step there, is on panel 5. We want the BAT CHARGER BAT A CHARGE circuit breaker closed, and the BAT CHARGER BAT B CHARGE circuit breaker closed. Over.

Okay. That's BAT CHARGER BAT A CHARGE, BAT CHARGER BAT B CHARGE, both closed on panel 5.

That's affirmative. We need them closed to power the switches. Next on panel 5, we want the EPS SENSOR SIGNAL MAIN A and MAIN B circuit breakers closed. Over.

Okay. Panel 5, CB EPS sensor's signals MAIN A and MAIN B closed.

Okay. That's affirmative. We need them closed so that you can read out your volts and amps. Next step, on panel 250, we want circuit breaker BAT A POWER ENTRY and POSTLANDING and BAT B POWER ENTRY and POSTLANDING, closed. Over.

Okay on panel 250, CB BAT A POWER, ENTRY and POSTLANDING, closed; BAT B POWER ENTRY and POSTLANDING, closed.

That's affirmative. And at that point, we'd like you to check the BAT bus voltages on both BAT buses to make sure we don't have any shorts. Over.

Okay. Read the BAT bus voltages on BAT BUS A and BAT BUS B.

That's affirmative. The next step on panel 275: circuit breaker MAIN A, BAT BUS A, closed, and circuit breaker MAIN B, BAT BUS B, closed. Over.

Okay. On 275, circuit breakers MAIN A, BAT BUS A, closed; MAIN B, BAT BUS B, closed.

That's affirmative. The next step on panel 5: we want the MAIN BUS TIE A/C switch to the BAT A/C position, and verify proper voltage on MAIN BUS A, and read the amps on BAT A to make sure we don't have a short. Over.

Okay. …

Okay, Jack; Houston. We're in bad COMM again; let's wait a minute.

Okay. How do you read …?

That's better, Jack. Go ahead with your readback.

Okay. Place MAIN BUS TIE A/C, on, read MAIN BUS A current and voltage.

Okay. That's affirmative. The next step will be the MAIN BUS TIE B/C switch to the on position and read MAIN B voltage and battery B amperage as above. Over.

Okay, MAIN BUS TIE B/C on; read MAIN B voltage and current.

Okay. That is correct. Then to reconfigure from this configuration, Jack, we want you to leave the MAIN BUS TIE switches in the on position and pull the circuit breakers out in reverse order that we had you close them. Over; and do you want me to read them up individually?

No, let me see if I've got it here. I go down to panel 275, open CB MAIN A, BAT BUS A and CB MAIN B, BAT BUS B. Then I go down to 250, and pull CB BAT A POWER ENTRY/POSTLANDING and BAT B POWER ENTRY/POSTLANDING and then up on panel 5, pull EPS SENSOR SIGNAL MAIN A, SENSOR SIGNAL MAIN B, BATTERY CHARGER BAT B CHARGE, BATTERY CHARGER BAT A CHARGE. And then close—I don't know whether you want me to close the RENDEZVOUS RADAR TRANSPONDER FLIGHT BUS and S-BAND TRANSMITTER/DSE FLIGHT BUS.

Okay, Jack. We don't want you to close those last two. Those are changes to your basic configuration, and we want to leave them open for now. Over.

Okay. I'll do that. Was the rest of the readback okay?

That's correct. Readback was 100 percent, and we'll wait to hear from you.

Okay, Joe. And just for confirmation, I went through the switch list you gave me. We are in exactly that configuration with one exception, and that is over on panel 382. I have not, the a—H₂O ACCUMULATOR is in the OFF position so that if we need any more water, we can get it.

Okay. Roger, Jack. Copy that. On panel 382, you've left the H₂O ACCUMULATOR valves in the OFF position, and we concur.

Okay. And there's one other thing that I don't know whether you're aware of. We have no lithium hydroxide canisters in panel two fif- in—canisters now. So when we get ready to power up, you'll have to remind us when you want us to add some.

Okay, Jack. We copy that. That's correct, and I'll add that to our basic checklist so that we won't forget it.

Okay. Real fine, Joe, and I'm on my way back into the command module.

Good deal.

Thank you.

How do you read, Joe?

And, Joe, how do you read Aquarius?

Aquarius, Houston. Pretty good. Go ahead.

Okay. I'm back on the line now, but Jack really … headed back to the upstairs bedroom.

Okay. Roger that, Fred.

Aquarius, Houston. Over.

Go ahead.

Okay, Fred. We recommend that you push your MASTER ALARM circuit breaker in so you'll have audio and visual on that, and, also, we medical types are getting to feel left out down here, and we'd like you to give us BIOMED … position, if you're plugged in for it, and we'll see whether it affects the voice or not. Over.

Okay.

Hey, Houston; Aquarius. On DOWN VOICE BACKUP S-band, how do you read me?

Okay, Joe. Go ahead.

Okay, Fred. This is a procedure for getting a read-out of the descent propellant tank temps. It's no big problem, but our LM people say that the bottom of the descent stage is probably cooling off, and we just want to verify that the descent water tank will be okay. Right now, it looks as though it won't freeze until several hours after it's empty, but we want to have you read these temperatures out to us so we can see how good our predictions are. The procedure is, on panel 16, close the PROPELLANT DISPLAY/ENGINE OVERRIDE LOGIC circuit breaker. Over.

Okay. The PROPELLANT DISPLAY OVERRIDE circuit breakers are closed. … the propellant.

Right, Fred. The next step is simply to turn the PROPELLANT TEMP PRESS MONITOR switch to DESCENT 1, read the fuel and OX temps, turn it to DESCENT 2, read the fuel and OX temps; tell us what they are.

Okay. On DESCENT 1, I get a fuel temp of 66.5 degrees, OX … on DESCENT 2, I get …

Okay, Fred. We're in noisy COMM here; I got DESCENT 1 fuel 66.5; stand by a second.

Okay. How do you read, now …?

That's better. Go ahead.

Okay. You got 66.5 on DESCENT 1 fuel temp, oxidizer temp is 66 degrees.

Okay. Copy —

On DESCENT TANK 2, fuel is reading 60—Okay. DESCENT 2 fuel is reading 68 degrees; oxidizer, 65 degrees.

Okay. Copy that, Fred. Thank you. We'd like you to pull the circuit breaker, and we'll probably come to you again in 5 or 6 hours for another check.

Okay. The panel 16 … … ENGINE … OVERRIDE is open.

Aquarius, Houston. Over.

Aquarius, Houston. Over.

Go ahead.

Okay. We're chasing a small glitch that we saw a while ago in the O₂ flow rate which is now normal again, but what we'd like you to do is, first of all, to tell us whether, during that canister procedure, you moved O₂ DEMAND REG A to any position other than CABIN, and then we'd like you to move it to OFF momentarily and back to CABIN for us.

Okay. To answer your question, Joe, it's no. I checked the CABIN all the time. Qualitatively, when we switched to this configuration, it didn't seem like the frequency or the suit fan noise … decreased … logged down a little bit, but I'll follow your procedure. You want me to take REG A, go to close and back to CABIN; is that correct?

That's correct, Fred.

Okay. We're in close.

Okay.

Now, I'm back to CABIN.

Okay. Thank you very much, Fred. I'll get back to you if we see anything.

(Music—The Age of Aquarius)

… Thank you.

Hey, have you guys got a woman on board?

No way I could handle that.