Spacelog Apollo 13

Okay, Joe. One thing I've noticed, that a couple of circuits there now—the pulse …—at least the number of them, is markedly decreased, and … rather bad and, apparently, that added venting we had out of the service module was some overboard relief valve, maybe letting go, because it appears to have stopped now.

Houston, Aquarius.

Aquarius, Houston. Go ahead.

What do you read down there for partial pressure CO₂?

Oh, let's see. We're reading 6.6 right now, Fred. What do you read?

I'm reading about 12.5. I guess we've got a gage problem … I did just get a MASTER ALARM and no caution light; we kind of figured that's what it was, with CO₂ approaching its limit. Maybe it didn't quite come out here.

Okay. Let me get a go, and I think it's time for us to go ahead and put these other canisters on. Stand by 1.

Okay. We went to 15 on the primary last night before I changed it and —

Roger that, Fred. We wanted to —

— I don't have a steady—I don't have a steady ECS light on at this time, Joe, so it must have just been a momentary.

Okay. We know when you went to 15 last night on primary. We want to switch out today at 7.6. Let me check and see if we're ready.

Okay.

Yes. That's what it is, Joe. I've got something going on this alarm … ECS light.

Fred, Houston. The COMM isn't too sharp and I didn't copy.

Okay, Aquarius; Houston —

Houston, Aquarius. How do you read?

— Why don't you try it now? You're loud and clear now, Fred.

Okay. I was just—I'm getting MASTER ALARMS every few seconds and I am catching a glimmer now of the ECS light. For the time being, I have …—… open. Okay, now we got the ECS light on steady.

Okay. Copy that. You have the MASTER ALARM, with the ECS light. We are ready to go ahead and get you on the command module canisters. And as the first step, I'd like to know whether you've inserted the commander's red hose to the second canister bag. Over.

Okay. Yes. Sure enough; the commander's red hose is inserted into the canister bag.

Okay, Fred. The next thing I'd like you to do is to take some more gray tape and tape over half the outlet area of each of the blue nozzles; the commander's and the LMP's. The reason we're doing this is we're going to be running this loop through the secondary LiOH canister hole with the canister removed, and we don't have the flow restriction we need to keep the separator from overspeeding. Over.

Okay. Yes, that's right. So we want to tape over half of the—both the blue and the red commander hoses. Is that right?

Negative, Fred. That's half of the commander's blue hose and half of the LMP's blue hose—the outlet hoses.

Oh, okay. I'll tape over half of each of the outlets. Stand by.

Okay. I'm going to turn off one suit flow valve at a time while I am doing the taping, Joe.

Say again, please, Fred.

Okay, while I'm doing the taping, I'll have that particular suit flow valve in the suit DISCONNECT position momentarily.

Okay, Fred. Is that done? Over.

No. That's still in works. I just wanted to comment you might pass on to Steve Grega, we thank you a lot for those rendezvous procedures. They went to making up these little boxes.

Okay. We appreciate your appreciating it. We're just having a ball down here working on all kinds of new procedures, Fred. The CPCB is in session, and we expect to have your entry procedures out here by Saturday or Sunday at the very latest.

Saturday or Sunday?

At the very latest!

Take your time, Jack.

Why don't you run that other hose back up in the tunnel so Jim can get some air.

And Joe, how you read now?

Satisfactory, Fred. Go ahead.

Okay. Back to the condensate container. I guess the only question I really need answered is will it leak?

Is will it leak? Oh, yes. Stand by 1.

And we've checked all the fittings and I know I can hook everything up to our UCDs. So, if it doesn't leak, we can transfer.