Spacelog Apollo 13

Okay.

Okay. And circuit breakers on panel 5 we want all open. Over.

Okay.

Okay. On panel 6, skip the first one. We want POWER to OFF, and skip down then to SUIT POWER to OFF. Over.

All right.

Okay. On panel 7 we want EDS POWER, OFF. TVC SERVO POWER 1 and 2, OFF; FDAI/GPI POWER, OFF; and LOGIC 2 slash 3 POWER, OFF. Over.

Okay. I'll read back. SUIT COMPRESSOR 1 and 2, OFF; FUEL CELL PUMPS 1, 2, and 3, OFF; G/N POWER, OFF; MAIN BUS TIES, OFF; INTERIOR INTEGRAL LIGHTING, OFF; INTERIOR FLOODLIGHTING, OFF; then coming down, all circuit breakers on panel open; panel 6, the POWER should be OFF; SUIT POWER should be OFF; panel 7, all 5 of those switches should be OFF.

Okay, Jack. That's correct. Go to page 1-7. SCS ELECTRONICS POWER, OFF; SCS SIGNAL CONDITIONER/ DRIVER BIAS 1 and 2, OFF; and BMAG POWER, both, OFF; and DIRECT O₂ valve to close. Over.

Okay. SCS ELECTRONICS POWER, OFF; both SIGNAL CONDITIONER/DRIVER BIAS POWER, OFF; BMAG POWER, two of them OFF; DIRECT O₂ to close.

Okay. Now on panel 8, I'm going to have to read you a number of circuit breakers that we want open, and so start with CB panel 8 all closed except leave the two that we have there CM/RCS HEATERS, open, and FLOAT BAG open, and add the following. I'll read them up one at a time, and you can Roger. SCS LOGIC BUS, four, to open. Over.

SCS LOGIC BUS, four, open.

Right. SPS PITCH and YAW, four, to open.

SPS PITCH and YAW, four, to open.

Roger. SPS GAGING, four, to open.

SPS GAGING, four, open.

Okay. And SEQ ARM, two, open.

Okay. Are you with me? SEQ ARM, two of them open.

Roger. The next is EDS, three, to open.

EDS, three, open.

Roger. The next are ELS BAT A, BAT B, two, open.

Okay. That was the—Yes, the POSTLANDING VENT, that's FLT/PL, to open. The next are SCS DIRECT ULLAGE, two, to open.

SCS DIRECT ULLAGE, two, open.

That's correct, and the next ones are SM RCS HEATER A MAIN B, and HEATER C MAIN B, open.

Okay, SERVICE MODULE RCS HEATER MAIN B, open, and HEATER C MAIN B, open.

That's correct, and SM RCS HEATER B MAIN A, open, and HEATER D MAIN A, open. Over.

Okay. Got those, too.

Okay, Jack. That's the last of the additions to this page. Go back to the regular checklist, and go to the AUTO RCS SELECT switches. We want all 16 of them open. Over. That is OFF.

Okay. Okay. They're sitting at OFF right now. All 16 AUTO RCS switches OFF.

Okay. Then we go down to interior NUMERIC LIGHTING-LIGHTING, OFF; INTERIOR INTEGRAL LIGHTING, OFF; and INTERIOR FLOOD LIGHTING, OFF. Over.

Okay.

Okay. Skip 3. We want SECs LOGIC, two OFF, down, and SECs PYRO ARM, two OFF, down. Over.

Okay.

Okay, and on panel 9: POWER to OFF. Over.

All right.

Okay, Jack. I don't think you need to read back all the circuit breakers because we copied them as you went. If you just want to read back—the panel 8, panel 9 changes.

All right, let's do it. SCS ELECTRONICS POWER, OFF. … panel 8. All 16 RCS switches, OFF. INTERIOR NUMERICS LIGHTING, OFF; INTERIOR INTEGRAL, OFF; INTERIOR FLOOD LIGHTING, OFF. SPS LOGIC, two, down and OFF. PYRO ARM, down and OFF. Then panel 9 is POWER to OFF.

Okay; that's correct, Jack. Let's go to page 1-8. In the second line, SUIT POWER's OFF. Over.

Okay.

Okay, Jack. COMM sounds a little —

— … too many changes here.

— COMM sounds better now, Jack —

Okay, we're back. We —

Good. SUIT POWER was OFF, and then go to panel 10, POWER, OFF, and SUIT POWER, OFF. Over.

Okay. I got it.

Okay. And that's the only changes on pages 1-8. Over.

Okay. SUIT POWER, OFF; panel 10, POWER and SUIT POWER, OFF.

That's correct. Go to page 1-9 and on panel 100, skip the first four. We want IMU POWER, OFF. Over.