- Vance Brand (CAPCOM)
-
Okay. Next page, power 7, panel 16. First row, close the four QUAD TCA circuit breakers, that is, QUAD 1, TCA; QUAD 2, QUAD 3, and QUAD 4 TCA. Okay. Rows 2, 3, and 4 are okay.
- Fred Haise (LMP)
-
Okay. Panel 16, top row, we want to close QUAD 1 through 4 TCA breakers, and you're saying the other three rows are as is. Again, I have the exception the ASCENT ECA CONTROL on 16 should also be open.
- Vance Brand (CAPCOM)
-
Okay, Fred. One addition, third row. The S-BAND POWER AMP. Request that you pull that circuit breaker and leave the switch in PRIMARY.
- Fred Haise (LMP)
-
Okay. Yes, that's the way we were doing it before. I'll pull the POWER AMP CB, and then I'll go back to the first stage and put the POWER AMP to PRIME.
- Fred Haise (LMP)
-
RESET, OFF and LOW. Okay. Lighting bus off; EXTERIOR LIGHTING is off. Okay. You want to get your breakers, Jim? We ought to probably go back to that wide deadband.
- Fred Haise (LMP)
-
Okay. Jim just noticed we got a VHF breaker in on panel 11 still, I think, that probably should be opened.
- Jim Lovell (CDR)
-
— but my only question is, I got the CROSS TIE BUS circuit breaker in? Could be—Yes, this one right here.
- Fred Haise (LMP)
-
Yes. We've managed the first 30 hours or so here without the caution and warning; we don't need to keep it up now, do we?
- Vance Brand (CAPCOM)
-
Okay, Fred. That's one that we're leaving up until the PTC is established. We have a procedure for PTC to try with you, which we're hopeful will work pretty well. And I'll read that up as soon as you get what you're doing now done.
- Jim Lovell (CDR)
-
Why don't you go ahead, and I'll get this PTC procedure. It's by the photo log, and I'll just get that.
- Fred Haise (LMP)
-
And one other question, Houston. You really want to pull the ASA breaker? You want to give up the AGS probably for good now, huh?
- Vance Brand (CAPCOM)
-
Okay. I'll get back with you on your question in a minute, Fred. New, here comes the PTC procedure. Step 1, GUIDANCE CONTROL to PGNS; two MODE CONTROL, ATT HOLD; VERB 76, ENTER; maneuver to PTC attitude; and that incidentally is roll 0, pitch 90, and present yaw. We realize you can't monitor that on your FDAI, but you can on a verb, with a VERB 16 NOUN 20.
- Jim Lovell (CDR)
-
Roger. GUIDANCE CONTROL, PGNS; MODE CONTROL, ATT HOLD, VERB 76, ENTER; maneuver to PTC attitude which is roll 0, pitch 90, and yaw, which is the present yaw. Is that correct?
- Vance Brand (CAPCOM)
-
That's correct. Okay. Next. Mode—at—When you're established at the attitude, MODE CONTROL AUTO. Key in VERB 16 NOUN 20 to monitor rates; when less than 0.1 degree a second, rate in all—in each axis, then disable plus-X thrusters. Okay. Next VERB 25, NOUN 07, ENTER; 1257, ENTER; 252, ENTER; 1, ENTER; VERB 77, ENTER; VERB 48, ENTER; put in the DAR 22110 and PROCEED; VERB 34, ENTER; then VERB 16, NOUN 20; and monitor rates. On rates less than 0.01 degrees per second in all axis: VERB 76, ENTER; MODE CONTROL, ATT HOLD; then 30 clicks of right yaw to start the maneuver. Over.
- Jim Lovell (CDR)
-
Okay, Vance. PTC procedure: GUIDANCE CONTROL, PGNS; MODE CONTROL, ATT HOLD; VERB 76, ENTER; maneuver to PTC attitude; roll 0, pitch 90, yaw 0; my ball now, of course, is inoperative, so I'll have to get that on the DSKY. The 5 is MODE CONTROL, AUTO; 6: VERB 16, NOUN 20, monitor rates; rates less that 1 degree per second in each axis, disable, and I didn't hear that last part. The next one was VERB 25, NOUN 07, ENTER; 1257, ENTER; 252, ENTER; 1, ENTER; VERB 77, ENTER; VERB 48, ENTER; 22110, PROCEED; VERB 34, ENTER; VERB 16, NOUN 20, ENTER; monitor rates. Rates less than 0.01 degrees per second in all axis. VERB 76, ENTER; MODE CONTROL, ATT HOLD; then 30 clicks of right yaw to stop—to start—maneuvers
Expand selection up Contract selection down Close - Vance Brand (CAPCOM)
-
Roger. That's correct, Jim. To—to answer your questions and correct one point, yaw should be your present yaw, whatever it is, and that's up with roll 0, pitch 90, present yaw. The other thing is, you said disable and you didn't hear the rest. That's disable plus-X thrusters. And, finally, near the end, the 22110 referred to DAP loading.
- Jim Lovell (CDR)
-
Roger. Now, to maneuver to PTC roll 0, pitch 90 and yaw in—and pitch in here, roll is here. Yaw—whatever yaw we have in. Okay, Vance. In our initial maneuver to PTC attitude, I am going to have to use—to display 16 20 and I'll have to use the TTCA to get there.
- Vance Brand (CAPCOM)
-
Jim, Roger. Your use of the TC—TTCA and just a reminder that in maneuvering that—that—that roll is in R3 and yaw is in R1.
- Jim Lovell (CDR)
-
That's affirm. And I'm going to take out roll first to get it zero and then I'm going to take care of pitch.
- Jim Lovell (CDR)
-
Okay. GUIDANCE CONTROL, PGNS; MODE CONTROL to ATT HOLD. VERB 73 clears. Okay. We've got to get that out. … it stopped moving.
Expand selection down Contract selection up - Vance Brand (CAPCOM)
-
Okay. A couple of things, Jim. One is that you can use the TTCAs to maneuver, but you're going to save a lot of fuel if you'd try MINIMUM IMPULSE. So, that might be a better recommendation. The other thing is, we'd like to give you a GO before you disable the plus-X thrusters, and before you do a VERB 76, and MODE CONTROL to ATT HOLD. Over.
- Jim Lovell (CDR)
-
Okay; understand. You want a GO before I—I'm—Of course, I just did a 76, and the MODE CONTROL is in ATT HOLD, at this time. But, this is later on down.
- Vance Brand (CAPCOM)
-
Yes. All we wanted to do was take a look at things before you disabled the plus-X thrusters, and before you go to MIN IMPULSE at the end there—that VERB 76, ENTER; MODE CONTROL, ATT HOLD.
- Fred Haise (LMP)
-
In what fashion did you want us to disable those plus-X thrusters? Just pulling those appropriate TCA breakers, or did you want to actually go in and mask those jets?
- Vance Brand (CAPCOM)
-
Okay, Fred. We didn't explain that. The VERB 25, NOUN 07, ENTER sequence does that.
- Fred Haise (LMP)
-
Okay. I didn't read the whole procedure. Jim just mentioned he wanted to disable plus-X.
- Fred Haise (LMP)
-
And, Vance, are you still trying to get me an answer on that—pulling that ASA breaker?
- Vance Brand (CAPCOM)
-
Okay. Just some info. We're working up a procedure for you to use to—to use command module LiOH canisters to connect to your hoses—the outlet hoses in the LM so that, as time passes in the mission, you can continue scrubbing the LM atmosphere. And this whole thing requires modifying a kit so that you can attach the hose modifying a LiOH canister, so you can attach the hose to it. So, sometime in the future, we will be coming up to you with that procedure. Second point—Second point in, we're standing by to watch your maneuver for the PTC procedure. Over.
- Jim Lovell (CDR)
-
Okay. I'm in process now, Vance, of maneuvering to zero yaw, 90-degree pitch, using MINIMUM IMPULSE.
- Fred Haise (LMP)
-
And, Vance, I assume it had also been brought up that we got two extra secondary cartridges—one in each PLSS.
- Vance Brand (CAPCOM)
-
Yes. We wish we could send you a kit and it would be kind of like putting a model airplane together or something. As it turns out, this contraption will look like a mailbox when you get it all put together.
Spoken on April 15, 1970, 3:14 a.m. UTC (54 years, 8 months ago). Link to this transcript range is: Tweet