Spacelog Apollo 13

Okay. Continue, Vance.

Okay. Next page, power 7, panel 16. First row, close the four QUAD TCA circuit breakers, that is, QUAD 1, TCA; QUAD 2, QUAD 3, and QUAD 4 TCA. Okay. Rows 2, 3, and 4 are okay.

Okay. Panel 16, top row, we want to close QUAD 1 through 4 TCA breakers, and you're saying the other three rows are as is. Again, I have the exception the ASCENT ECA CONTROL on 16 should also be open.

Okay. We concur on that, and we have a late arrival in row 3. Stand by.

Okay, Fred. One addition, third row. The S-BAND POWER AMP. Request that you pull that circuit breaker and leave the switch in PRIMARY.

Okay. Yes, that's the way we were doing it before. I'll pull the POWER AMP CB, and then I'll go back to the first stage and put the POWER AMP to PRIME.

That's correct; that should be changed back to PRIME. And that's—that's it.

Good work, Vance.

Thank you.

RESET, OFF and LOW. Okay. Lighting bus off; EXTERIOR LIGHTING is off. Okay. You want to get your breakers, Jim? We ought to probably go back to that wide deadband.

Okay. The BUS TIE INVERTERs are coming off the line.

Yes. Go ahead. Sorry, I put the switch off, that'll kill caution and warning.

Okay. Let's see. So we're going to lose the ball again.

Yes.

I'll get 16 NOUN 20 out.

Do you have me move AUTO TRANSFER this time?

Why do I still have a VHF-A receiver off?

You don't, do you?

Yes.

And one other question, Houston. You really want to pull the ASA breaker? You want to give up the AGS probably for good now, huh?

Houston, I'm standing by to copy the PTC procedures.

Okay. I'll get back with you on your question in a minute, Fred. New, here comes the PTC procedure. Step 1, GUIDANCE CONTROL to PGNS; two MODE CONTROL, ATT HOLD; VERB 76, ENTER; maneuver to PTC attitude; and that incidentally is roll 0, pitch 90, and present yaw. We realize you can't monitor that on your FDAI, but you can on a verb, with a VERB 16 NOUN 20.

With me?

Roger. GUIDANCE CONTROL, PGNS; MODE CONTROL, ATT HOLD, VERB 76, ENTER; maneuver to PTC attitude which is roll 0, pitch 90, and yaw, which is the present yaw. Is that correct?

Okay, Vance. PTC procedure: GUIDANCE CONTROL, PGNS; MODE CONTROL, ATT HOLD; VERB 76, ENTER; maneuver to PTC attitude; roll 0, pitch 90, yaw 0; my ball now, of course, is inoperative, so I'll have to get that on the DSKY. The 5 is MODE CONTROL, AUTO; 6: VERB 16, NOUN 20, monitor rates; rates less that 1 degree per second in each axis, disable, and I didn't hear that last part. The next one was VERB 25, NOUN 07, ENTER; 1257, ENTER; 252, ENTER; 1, ENTER; VERB 77, ENTER; VERB 48, ENTER; 22110, PROCEED; VERB 34, ENTER; VERB 16, NOUN 20, ENTER; monitor rates. Rates less than 0.01 degrees per second in all axis. VERB 76, ENTER; MODE CONTROL, ATT HOLD; then 30 clicks of right yaw to stop—to start—maneuvers

Roger. That's correct, Jim. To—to answer your questions and correct one point, yaw should be your present yaw, whatever it is, and that's up with roll 0, pitch 90, present yaw. The other thing is, you said disable and you didn't hear the rest. That's disable plus-X thrusters. And, finally, near the end, the 22110 referred to DAP loading.

Roger. Now, to maneuver to PTC roll 0, pitch 90 and yaw in—and pitch in here, roll is here. Yaw—whatever yaw we have in. Okay, Vance. In our initial maneuver to PTC attitude, I am going to have to use—to display 16 20 and I'll have to use the TTCA to get there.

Jim, Roger. Your use of the TC—TTCA and just a reminder that in maneuvering that—that—that roll is in R₃ and yaw is in R₁.